![Infinity RS Force V3 1400mAh 6S 130C 22.2V LiPo Battery XT60 [DG]](http://www.fpvfaster.com.au/cdn/shop/products/1_c8e3300c-2e6b-4dcc-9e6d-a1a958e8bf93_300x300.jpg?v=1645153546)
HappyModel Crazybee Pro V3 F4 2-4S Flight Controller AIO Brushless Whoop Mobula7 Mobula7 HD
Notes:
The biggest differences between Crazybee F4 PRO V1.0, V2.0 and V3.0 are:
V2.0 could handle 1-3s Lipo/LiHV
V1.0 could handle only 1-2s Lipo/LiHV
V2.0 use bigger bind and boot button , change the BAT/GND pad to “through hole”
V3.0 supports 2S – 4S LiPo, ESC upgraded to 10A. A few things have gone back to how it was before due to the lack of space: no longer using plastic connector for VTX and camera, just solder pads now; And bind and boot buttons reverted back to the original tiny ones
Specification:
| (Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS (No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 7-17V) Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Current meter scale set to 470 Built-in 5V 1A BEC Built-in voltage detection |
| MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 10A continuous peak 12A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_5.HEX Default protocol: DSHOT600 |
| SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
| SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
| No RX version support external serial-bus receiver like XM+, crossfire, S-FHSS etc. |
Package Included:
1x CRAZYBEE PRO V3.0 Board
1x Power Cable
![Infinity RS Force V3 1400mAh 6S 130C 22.2V LiPo Battery XT60 [DG]](http://www.fpvfaster.com.au/cdn/shop/products/1_c8e3300c-2e6b-4dcc-9e6d-a1a958e8bf93_600x600.jpg?v=1645153546)
